Malco C5A2 Impact Power Assisted Crimper

Brand:Malco

3.4/5

227.18

Η κρούση turbo crimper Malco είναι ένα απλό, συμπαγές αξεσουάρ που λειτουργεί αποκλειστικά με την υποβοήθηση ισχύος της τεχνολογίας πρόσκρουσης Driver για ασφαλή και αποτελεσματική πτύχωση γαλβανισμένου στρογγυλού αγωγού 30 έως 24 (0,41 έως O,71 mm) και μαύρου (0,31 έως 0,61 mm) σωλήνας σόμπας. Η πρόσκρουση του στροβιλοπτέρυγα δεν απαιτεί ρύθμιση ή ρύθμιση. Απλώς κουμπώστε τον άξονα μετάδοσης κίνησης τροφοδοσίας 1/4 ιντσών στον ασύρματο ή ενσύρματο (ελάχ. 12 volt DC / μέγ. 7 amp. AC) κρουστικό οδηγό για να ξεκινήσετε αμέσως τη πτύχωση πολλαπλών μεγεθών, τύπων και πάχους σωλήνα και αγωγού, συμπεριλαμβανομένου του σπειροειδούς αγωγού. γρήγορα και εύκολα. Με τη ραφή σωλήνα ή αγωγού σε κλειστή θέση, ξεκινήστε τη πτύχωση στη μία πλευρά της ραφής τραβώντας απαλά τη σκανδάλη του προγράμματος οδήγησης και στρέφοντας την πρόσκρουση του στροβιλοπτέρυγα στη μεταλλική άκρη. Περπατήστε το Crimper γύρω από την περιφέρεια του σωλήνα με ελεγχόμενο τρόπο και στη συνέχεια γωνίστε το Crimper από το μέταλλο καθώς το Crimper πλησιάζει την άλλη πλευρά της ραφής. Η πρόσκρουση του στροβιλοπτέρυγα είναι πέντε φορές πιο γρήγορη από ένα χειροκίνητο εργαλείο σύσφιξης που βασίζεται σε δοκιμές πραγματικού πεδίου! Είναι άνετο για κάθε χειριστή να κάνει ελιγμούς και, όπως λαμβάνουν υπόψη οι αριστεροί, λειτουργεί με το σύστημα οδήγησης πρόσκρουσης προς τα εμπρός ή προς τα πίσω. Η εύχρηστη μικρή κρούση turbo crimper είναι ένα απαραίτητο αξεσουάρ για κάθε εγκαταστάτη HVAC και αποθηκεύεται εύκολα σε μια θήκη ή τσάντα έτοιμου εργαλείου όταν δεν χρησιμοποιείται.

Αποθηκεύεται σε θήκη ή τσάντα. Συμπαγές, εύκολο στους ελιγμούς και ισορροπία. Καμία ρύθμιση ή ρύθμιση. Κρυφές 30-24 ga. (0,41-0,71 mm) στρογγυλός μεταλλικός αγωγός. Γρήγορα κάνει το πρόγραμμα οδήγησης πρόσκρουσης ηλεκτρικό τσακιστή.
Batteries Included? ‎No
Batteries Required? ‎No
Brand Malco
Brand ‎Malco
Color Black
Color ‎Black
Country of Origin ‎USA
Customer Reviews 4.4 4.4 out of 5 stars 662 ratings 4.4 out of 5 stars
Grip Type ‎Ergonomic
Handle Material Metal
Handle Material ‎Metal
Is Discontinued By Manufacturer ‎No
Item Dimensions LxWxH 8.25 x 6 x 2 inches
Item Dimensions LxWxH ‎8.25 x 6 x 2 inches
Item model number ‎C5A2
Item Package Quantity ‎1
Item Weight 2.1 Pounds
Item Weight ‎2.1 Pounds
Manufacturer ‎Malco Products
Material ‎steel
Measurement System ‎Metric
Part Number ‎C5A2
Power Source ‎Hand Powered
Product Dimensions ‎8.25 x 6 x 2 inches
Style ‎Crimper
Warranty Description ‎Limited

3.4

12 Review
5 Star
73
4 Star
11
3 Star
5
2 Star
3
1 Star
8

Γράψτε την κριτική σας

Το email σας δεν θα δημοσιευτεί. Όλα τα υποχρεωτικά πεδία επισημαίνονται με*

Scritto da: Anthony
Absolute wrist saver
I’ve done hvac for over 4 years now hand crimping spiral and snap lock sheet metal and once I bought this my efficiency shot through the roof. Great crimps every single time super easy to use, durable, and easy on your impact great purchase
Scritto da: Kristina Kreitzer
Better than hand crimpers
I’m a union sheet metal worker, and this thing is awesome. A bit of a learning curve l, but once you get the hang of it there’s no turning back. This thing has some weight to it which surprised me at first, but after using it I understand why. I’ve been looking at buying this for about a year, finally pulled the trigger and I’m glad I did. 5 secs is all it takes to crimp a pipe and it’s a close to a factory edge. I stop before the seam afraid to blast through it, though I’m sure it will handle it. Im very happy have to wait to see how long the shank lasts.
Scritto da: Ed
On the pricey side but faster than hand crimping
I was skeptical about buying this because it's not cheap. Hand crimpers are a lot cheaper. But I'm very impressed at how it crimps. It's noisy and you can only use it with a impact. I tried using it with my regular drill and it twisted the pipe and cut my arm so do not use anything but an impact it even has a warning label. But if you're crimping lots of pipe there's no competing with a hand crimper at how fast you can use this. Definitely worth the money if you are made of it.
Scritto da: Scott Messina
Saves your forearms
This is much faster than hand crimping, and far easier on your hands and forearms. I can crimp a 10" duct in about 10 seconds, while it's already mounted. Because this goes on the end of your impact, it can spin 360 to modify duct that's already in the air, as long as you've got 2+ inches all of the way around. Just don't go over a seam, it says so right in the instructions. It takes a few tries to learn the best way to get it fully engaged on the pipe, I just go forward a couple of clicks, then reverse back to the starting point, and it's ready to go. I am using it with a Milwaukee M12 Surge impact, so it's noise level isn't too bad. With a standard impact, it will likely be quite loud, especially when amplified by uninsulated ducting
Scritto da: Jason
Must have? Or nice to have? That’s the question.
It’s quit useful and saves tons of time if your cutting a lot of duct. There is one issue I have come across. I found that using this with fittings, like els, I found the crimp isn’t enough. I need to hand crimp a bit because it’s not quite enough to fit the duct to the fitting. Still worth it and a valuable tool. Is it a must have? I wouldn’t say that. But I’m very happy with it and do recommend it.
Scritto da: Placeholder
Great product
Thus is so fast and saves so much time when installing metal ducting, it’s a great tool
Scritto da: James
Worth it!
If you do much work with round sheet metal ducting this is worth it, in one job I used it so many times I didn’t even think I would need it and it saved so much time, it’s far quicker and results in more professional look than a hand crimper. It takes a little getting used to though but after that it’s awesome
Scritto da: Duct Sealant Joe
Fantastic, but....
Month in and is already wearing out a little bit. Works maybe a little too well. Will over crimp things by a half inch for circular duct. Otherwise it saves my time, and my hands. Would recommend
Scritto da: Tyler little
Beware! Can become a 270$ tool quickly
This thing is awesome! It crimps spiral better than you get from the shop, that being said if you push it too hard or try to crimp over a seam the drive shaft will snap. Malco has you covered though for almost 70$ they will send you a replacement shaft which is little more than a nut driver (10mm I think) with a shoulder at the end to hold it to the tool. If this easily replaceable, and easily broken part was a reasonable price this thing would get 5 stars all day. If you have a friend with a metal lathe maybe you can whittle up a cheaper replacement.
Scritto da: Jeff Arbeau
Forget what you know about crimping! 2ND REVIEW
The media could not be loaded. You have to learn how to use this tool. This crimper is nothing like any way you crimped before. Go low and slow till you ght the fell of it. Wish I had this 20 years ago. I love it!!
Scritto da: Brendon Maclellan
Awesome
This thing save so much time and energy. Love it. Highly recommended
Scritto da: Amazon Customer
Crap
Its crap. It rips apart ductwork and when you are super careful and actually get it to crimp all the way around it doesn't even crimp it enough for it to fit.

Σχετικά προϊόντα

hot
WEICON Duo-Crimp No. 300
3.6/5

€ 100.21

WEICON Duo-Crimp No. 300
3.6/5

€ 100.21

Ανακαλύψτε το διεθνές μας δίκτυο

Στέλνουμε σε 28 χώρες, πάνω από 200.000 προϊόντα. Μείνετε ενημερωμένοι, εγγραφείτε στο ενημερωτικό δελτίο.

Array