Flair-It Sales 10800 Plastic Bend Support, Μέγεθος 0,5'

Brand:FLAIR-IT SALES

3.5/5

28.87

Προσφέρουμε τη μεγαλύτερη συλλογή προϊόντων Υδραυλικών PEX. Έχουμε λύσεις για κάθε ανάγκη Υδραυλικών PEX κατοικιών! Ονομάστε το, το έχουμε. Διαθέτει το νέο υδραυλικό σύστημα PEXLOCK που χρησιμοποιεί μόνο οικιακά εργαλεία. Τα πάντα για το PEX, συμπεριλαμβανομένων των δακτυλίων πτύχωσης από ανοξείδωτο χάλυβα PEX και χαλκού PEX. Ecopoly πλαστικά εξαρτήματα πτύχωσης PEX, εξαρτήματα Flair-It PEX & πολυβουτυλένιο, συλλέκτες Flair-It PEX, προϊόντα εγκατάστασης PEX, σωλήνες PEX ακτινοβολίας, σωλήνες pert, σωλήνες safepex (PEX a), καλύτερες σωλήνες PEX (PEX B), ανυψωτικά PEX, Κόφτες σωλήνων PEX, Crimpers PEX, κιτ επισκευής σέρβις PEX και οθόνες καταστημάτων λιανικής PEX.

Αριθμός ανταλλακτικού: 10800. Χώρα προέλευσης: Κίνα. Βάρος συσκευασίας: 1 κιλό. Διαστάσεις συσκευασίας: 5,5 L x 3,25 Υ x 1,0 W (ίντσες).
Brand FLAIR-IT SALES
Color Copper
Country of Origin China
Domestic Shipping Item can be shipped within U.S.
Exterior Finish Stainless Steel
International Shipping This item can be shipped to select countries outside of the U.S.
Item model number 10800
Manufacturer FLAIR-IT SALES
Material Plastic
Number of Pieces 1
Package Dimensions 5.39 x 2.52 x 0.87 inches; 0.63 Ounces
Size 0.5
Thread Size 0.5 inch

3.5

9 Review
5 Star
61
4 Star
21
3 Star
19
2 Star
0
1 Star
0

Γράψτε την κριτική σας

Το email σας δεν θα δημοσιευτεί. Όλα τα υποχρεωτικά πεδία επισημαίνονται με*

Scritto da: Amazon Customer
Works as expected
Perfect for bending PEX. Great product and better than splicing to get the angle.
Scritto da: C. Anderson
Work and affordable but Sharp and too much packaging
The per piece packaging is annoying. It was better when then were 10 piece. Price is better than box stores. They are sharp, as others stated, but this did not affect the Pex. Have not had a problem with the lines popping out of the bend support, but lines have only been pressurized with air so far.
Scritto da: T. Davidson
Sharp flashing from mold cuts into your hands when bending PEX into these
The manufacturing injection mold leaves sharp edges that will cut into your hands, wear heavy gloves when working with these.
Scritto da: AlexCphoto
Work great
These work great, not only save you from adding two additional failure points to your lines with additional crimps for a 90deg L but also saves you a bit of $ and time / effort. Takes a bit of strength to use but so does crimping.
Scritto da: Jonathan Wieder
Kind of like a mound was only 90% filled with plastic
The ones I received were black. They seemed to be mis-cast, as the lip that receives the zip tie was only partially there. Kind of like a mound was only 90% filled with plastic. Didn't really affect the usability. Would buy again.
Scritto da: frankievis52
Nice Quality.
Great product for the price. Used it for Plex tubing and it worked great.
Scritto da: lee westmoreland
Not available in big box stores
The metal version of this is available in big box stores locally but the cost is about 3 times more than these. So far, so good - they seem to work very well.
Scritto da: Banned for honest reviews
They may do the job, just be careful that they don't slash your hand open when you install them.
These are fine for the job, but be careful handling them, since they are very poorly molded. The "flash" at the mold seam is bad enough that it can easily cut your hands up. They seem to me to be manufacturer's rejects. No normal retailer would accept these in to their inventory.
Scritto da: Amazon Customer
Works well
This piece works well. It comes with a few rough edges but with a file, some sandpaper and a couple of minutes they were all gone. No worries about kinking the pipe with this and it gives you a way to secure the pipe to the wall or ceiling.

Σχετικά προϊόντα

Ανακαλύψτε το διεθνές μας δίκτυο

Στέλνουμε σε 28 χώρες, πάνω από 200.000 προϊόντα. Μείνετε ενημερωμένοι, εγγραφείτε στο ενημερωτικό δελτίο.

Array