Big Horn 18823 1-Phase, 220-240-Volt, 3-HP, 18-26-Amp Magnetic Switch - Εγκεκριμένο CSA

Brand:BIG HORN

3.5/5

112.51

ΠΕΡΙΓΡΑΦΗ ΠΡΟΪΟΝΤΟΣ Εφαρμογές: Όλες οι μηχανές που χρησιμοποιούνται για κινητήρες εφαρμόζονται σε ΜΑΓΝΗΤΙΚΟΙ ΕΚΚΙΝΗΤΕΣ, όπως: μηχανή διάτρησης, μηχανή περιγράμματος πρέσας (πριονοπρίονο), ραπτομηχανή, μεταφορική μηχανή, μηχανή συσκευασίας, αεροσυμπιεστής, αντλία αέρα, κλιματιστικό και συγκεκριμένα μηχανή κτλ.

Δεν υπάρχουν διαθέσιμες μονάδες
✅ 50 HZ @ 240V & 60 HZ @ 220V. ✅ Εγκεκριμένο CSA. ✅ Κομψή εξωτερική, βαριά διάρκεια ζωής, εύκολη λειτουργία. ✅ Μεγάλη μηχανική και ηλεκτρική αντοχή του επαφέα. ✅ Ανυψωμένο κουμπί OFF και ενσωματωμένο κουμπί ON για έκτακτη ανάγκη. ✅ Προστασία από σκόνη και αδιάβροχο. ✅ Προστατέψτε τον εξοπλισμό από υπερφόρτωση λόγω απροσδόκητης εκκίνησης και διακοπής ρεύματος.
Actuator Type Push Button
Actuator Type ‎Push Button
Batteries Included? ‎No
Batteries Required? ‎No
Brand BIG HORN
Brand ‎BIG HORN
Controller Type ‎Push Button
Country of Origin ‎China
Current Rating 18 Amps
Current Rating ‎18 Amps
Customer Reviews 4.4 4.4 out of 5 stars 276 ratings 4.4 out of 5 stars
Domestic Shipping Item can be shipped within U.S.
International Protection Rating IP54
International Protection Rating ‎IP54
International Shipping This item can be shipped to select countries outside of the U.S. Learn More
Item Dimensions LxWxH 5 x 4 x 6.5 inches
Item Dimensions LxWxH ‎5 x 4 x 6.5 inches
Item model number ‎18823
Item Package Quantity ‎1
Item Weight ‎2.09 pounds
Manufacturer ‎Big Horn
Mounting Type Surface Mount
Mounting Type ‎Surface Mount
Number of Positions 1
Number of Positions ‎1
Operating Voltage 240 Volts
Operating Voltage ‎240 Volts
Operation Mode Off,Push Button
Operation Mode ‎Off,Push Button
Part Number ‎18823
Product Dimensions ‎5 x 4 x 6.5 inches
Switch Style Push Button
Switch Style ‎Push Button
Unit Count ‎1.0 Count

3.5

13 Review
5 Star
69
4 Star
16
3 Star
8
2 Star
2
1 Star
5

Γράψτε την κριτική σας

Το email σας δεν θα δημοσιευτεί. Όλα τα υποχρεωτικά πεδία επισημαίνονται με*

Scritto da: James Todd Cheek
It's OK for what it is
The housing cracked when trying to put the wire glands in, also it is very difficult to feed the wire up into the box
Scritto da: Wally Weasel
Works well on a 2 HP 220V planer.
I installed this myself and found a few things I thought I might share. First, the threads for the "cable gland", which is the strain relief for your wires as they come into the box are metric M20x1.5. If you want the wire strain reliefs to fit perfectly just buy a couple of those so you have them when you need them. A M20x1.5 cable gland is available on Amazon and will fit up to a 12/3 SJOOW wire. They are similar in size to USA half inch thread strain relief but not the same. Also, there is a sticker inside the box lid that shows the wiring diagram, no other paperwork in box. Mine came kinda scratched up but legible. The lid has plastic screws that seem a bit delicate.... definitely be careful to not strip the threads. If you don't know this already, a good trick to not strip threads is to put the screwdriver on and go backwards, counterclockwise, until it clicks, then twist clockwise gently with just your fingertips on the screwdriver. No powertools on this. The box itself is not super tough, I don't know how good it would do in an industrial or school setting but seems plenty fine for my use. If I clobber it with a piece of wood I think I might smash it. A metal box would be stronger but more money of course. The unit itself is made in Taiwan by Shern Dian Electric. It looks to be well made I would buy another if I needed it.
Scritto da: Richard BATES
Perfect Replacement
Direct replacement for worn out magnetic switch on my 3HP single phase Trupro saw bench. Works great and arrived in record time. Thanks heaps Amazon :-)
Scritto da: Bill Babbitt
Works great, but had broken parts
When I received this, it appeared to have been tampered with. Screws and small parts were floating around inside and plastic pieces were broken. I pieced it together and installed it anyway. It works great, but be sure to inspect it when you receive the unit.
Scritto da: Andy
Not an exact replacement but it Works well with a 3hp 10” Delta Unisaw.
Early 2000s Delta Unisaw X5 power switch replacement. This switch works well as a reasonably priced replacement for my 3hp 10” Delta Table saw’s magnetic switch. I gave it four stars not because of the quality, it works flawlessly because of two reasons. It is not an exact replacement and the job required drilling one hole and replacing the mounting bolts. The one thing I would change is I would like to have a large paddle switch over the stop button to hit with my knee in an emergency. Otherwise it’s a great product and 1/4 the cost of other options.
Scritto da: JDK
Great value and easy install
Replaced switch on my Unisaw with this particular switch, as the OEM replacement was insanely expensive. This switch was a welcome alternative both in terms of value and ease of install. Like others have mentioned, be sure to pick up 6-12mm cable glands to ensure a solid fit for the power and motor cables. I used the existing Unisaw switch bracket for the mount by drilling a new hole to match into it that was compatible to a good location inside switch for the respective mounting screw. This meant that I had to drill a hole into back of switch wall as well. Some have complained about the off button being too small. Search for DIY plans in building your own paddle assist to compensate if this is an issue for you. For example, go to lumberjocks dot com and search for project 318193.
Scritto da: R. Southworth
Great Replacement Motor Starter
This is a great replacement for my Delta Unisaw motor starter. The stock unit kept cutting out after 5 minutes because the thermal overload section was bad. Wiring for this one was super easy. I only gave it 4 stars because the thread on the box for the wire clamps is not right. I had to grind the threads down with a Dremel tool to get to fit. Lastly, I need to build a paddle to be able to hit the off button with my knee. The red button is too small. All things that were fixable though. The savings over an OEM unit was well worth the aggravation.
Scritto da: Jeremy
Worked great for me.
Installed it on a Grizzly 3HP table saw. Actually moved the magnetic switch box from inside the cabinet to outside of the saw replacing the paddle switch. Better price here on amazon as well. It's the exact import box everyone else sells. Just re-branded name. Wish we had an American made version
Scritto da: Robert G.
tres bien
tres bon produit
Scritto da: Martin Ricard
Fonctionne bien!
J’ai installé sur mon banc de scie 3hp Fonctionne très bien! Le seul défaut que j’ai trouvé, c’est les deux vis en plastique qui retient le couvercle. Les vis sont très fragiles. Elle ont cassé très facilement au serrage. J’ai dû remplacer par des vis en métal.
Scritto da: Leo P.
Magnetic Switch
bench saw Works perfect
Scritto da: Samuel Lessard
Bien mais....
Le bouton poussoir start reste coller dans le boitier en position enfoncé, c'est dangereux car lorsque l'on veux arreter la puissance , le moteur redemarre tout seul* je doit donner quelques tape sur le boitier pour que le bouton vert tombe en position neutre... je suis sure qu'il s'agit cependant d'un cas isoler parmi ce produits... somme tout le produits est bien !
Scritto da: Chad
Works great easy to install
Replaced the old switch that was acting up on a 3HP delta cabinet saw with this, it has been working great, pretty self explanatory how to hook it up, the only thing is the stop button is a little bit smaller than the old one but you could probably modify the button by gluing something on to make it bigger.

Σχετικά προϊόντα

Ανακαλύψτε το διεθνές μας δίκτυο

Στέλνουμε σε 28 χώρες, πάνω από 200.000 προϊόντα. Μείνετε ενημερωμένοι, εγγραφείτε στο ενημερωτικό δελτίο.

Array